evenheat kiln error codes

Evenheat kiln error codes can indicate that there’s something wrong with the kiln’s electrical system. The most common issues are a burned element, weared out element, loose connections, circuit breaker tripped, and uneven load. Then, you should take steps to correct the problem.


Weared out element

When your Evenheat kiln displays error codes, you should pay close attention to what the error code stands for. The error code itself is typically an “E” followed by a number or letter, such as “E-1.” The error code can help you determine what is wrong with your kiln, and can help you identify a solution.

First of all, you may want to check your electrical connections. They can become loose after about 10 firings. If they have become loose, it could be a sign that the element is worn out. If you find loose connections, you should immediately disconnect the kiln from the power source. Also, make sure the wires are not touching each other or the outside of the kiln jacket.


Next, check the element resistance. Some elements wear out over time, and their resistance increases, reducing the amount of power available to the kiln. This can result in longer firing times and higher cones. To check the resistance of your elements, you can use an Ohm meter. Make sure the readings match the model and voltage, and make sure you check the phase as well. If the resistance is higher than this, you may need to replace the element.

If this is the case, you may be able to determine what the problem is. You can check the ohms by clamping an “on” type ammeter around the “hot” power lead. You may also be able to identify the problem using a voltmeter.

Loose connections

A loose thermocouple connection can cause an Evenheat kiln error code. When a thermocouple is loose, it causes a computer to think the kiln is hotter than it really is. To fix this issue, you can reconnect the thermocouple wires, or check their sizing.

In order to check the amperes, you can clamp an amp meter around the hot cable. Be sure to remove any jumpers from the power cord. You may also notice an arc, which can be visually seen or smelled. If you are unsure of what is causing the arc, contact a licensed electrician for assistance.

You can also check the power switch. This may be the cause of the problem. If it is too loose, it may cause the power to cut off. If you close the door, the power will come back on. Check the wiring and adjust the switch. Ensure that all connections are tight.

If the power supply is out, the kiln may not be working properly. There may be loose connections or a faulty thermocouple. If the error continues, contact the manufacturer of your kiln. Once you determine the source of the problem, you can perform a repair.

Loose thermocouple connections can lead to a dangerous fire. A loose thermocouple can also cause a temperature drop. Be sure that all thermocouple connections are tight. If they are not, you can replace them and start heating the kiln again.

Circuit breaker tripped

If your circuit breaker has tripped on an evenheat kiln, it’s likely because the kiln has a dead short. A dead short causes large amounts of electricity to flow through the wires. The circuit breaker will automatically trip when this happens, so it’s important to check to make sure that it’s not the fault of the kiln itself.

First, check the size of your circuit breaker. If the breaker is over 69 amps, you’ll want to connect it to a 60-amp circuit. Otherwise, you’ll need to use a 50-amp circuit. Also, if the breaker won’t reset after restarting the program, it means the breaker is shorted to ground somewhere else in the control circuit. You can also check the resistance of your kiln by using a wheatstone bridge.

If the circuit breaker has tripped, check the wiring around the circuit breaker. Sometimes, this is the result of a loose connection. If this is the case, you can check the wiring by unplugging the circuit breaker from the wall.

The breaker itself isn’t a faulty component; it’s just a faulty switch or relay. If the coil isn’t red, then it’s working properly. If it is, then it is possible to touch a piece of paper to it to see if it burns. If it doesn’t burn, then the coil is getting enough power. You can also check the coil with a voltmeter.

Uneven load

If you notice that your kiln has an uneven load, you should check the power supply. Some kilns come with a flat type power cord that has two power #6 wires and two power #8 wires. To check the amperes, clamp an ammeter around the “hot” power cable. Then, check the total amperes by comparing the readings to the nameplate amps.

In some cases, an uneven load will result in an uneven temperature. This can occur if the vent system pulls too much air. This will cause the elements at the top of the kiln to be hotter than those near the bottom. If this happens, you may have to increase ventilation.

To fix the problem, you need to know how much the load will expand and contract during the firing process. Uneven heating will lead to cracks on wide pieces. Also, it is important to keep the edges of the stack a few inches from the sides of the kiln.

Uneven load can be prevented by making use of multiple thermocouple systems in different zones. These thermocouple systems will indicate the temperature more accurately. When using one thermocouple in each zone, you should make sure the thermocouple’s welded end is inserted at least 1/8″ deep into the chamber.


Overheating can be caused by several factors. It can be the result of a worn heating element or a faulty relay. Other factors include burnt wires or electrical noise. In either case, it is important to contact the manufacturer of the kiln to determine the cause of the overheating.

Evenheat kiln error codes often indicate a problem with the thermocouple. When the temperature sensor is not working properly, it causes the computer to think that the kiln is hotter than it really is. The solution is to tighten the connection or replace the temperature sensor.

The temperature E-1 may also be a sign of an uneven load. If the load is too high, the kiln may overheat. In this case, the load should be at least one inch above the thermocouples. Also, make sure the thermocouple is immersed to the right depth. It should be about l-l/2 inches into the kiln chamber.

The temperature of the control panel should be less than 125 degrees Fahrenheit. If the temperature is above this, a circuit breaker may need to be installed. It is important to monitor the temperature of the board and other critical parts. If you notice arcing, you should contact a qualified electrician to make the necessary repairs.

There are several causes of overheating. First, the electrical service to the kiln may be improperly wired. A qualified electrician should check the wiring from the main service to the kiln. Another common cause is that the kiln’s circuit is overloaded. It’s also important to turn off all appliances while operating the kiln.


Evenheat kiln error codes are the result of a variety of problems. One of these is a slow ramp. This means that the temperature will not increase quickly enough for the kiln to fire. It can also be a symptom of a broken heating element or a faulty relay. If you notice that your kiln has this error, it’s best to contact the manufacturer of your kiln to have it repaired or replaced.

There are many reasons why the E-1 temperature code is displayed. One of the most common causes is an uneven load. If you want to avoid this problem, try putting a bottom shelf underneath the element. Next, place the next shelf on an eight-inch post to ensure that the two elements shine into the bottom area.

The electrical circuit to your kiln may be overloaded. If you have other appliances plugged into the same circuit, they could have tripped the circuit. If you’re unsure, check the connections to your kiln to make sure they’re secure and tight. If a fuse blows or the circuit breaker goes off immediately, it’s likely a short circuit. In this case, a qualified electrician will need to diagnose your kiln and determine the cause.

Ensure that the thermostat and power switches are in good condition. You may need to check the wiring or replace an element if necessary. If you’re unsure, you can check the voltage by using a “clamp on” type of ammeter.